Ph. No- 9891925778   

PRODUCTS
 

     

    CAM BOX WITH PROXYMATRY

Rotating limit switch cam box with wide range from 3cam to 16 cam having rugged aluminum case with heavy duty shaft and life time sealed Ball-bearing provide the most versatile & dependably.

Spring Loading cam are provide for presion cam setting obtain for any angular position of the cam shaft from 0 to 360 degree.

Rotating Direction                                           Reverse Or Forward
Maximum Rotating Speed.                              1000 and above SPM.
Angle between the tooth                                  5 Degree. 
Shaft Out put                                                   Dia 16H7
Voltage                                                              24Volt DC and 230 Volt AC

 
 
  CAM BOX WITH DIAL INDICATOR


Rotating cam limit switch Box assembly. With Rugged aluminum case and heavy duty shaft and life time sealed Ball-bearing with Angle Position Dial indicator can be provided   on one end (on customer). demand.

  • Conventional Type 3cam., 6cam, 8cam.
     
  • Modular type from 3 cam to 16 cam.
 
 
  MODULAR CAM BOX

This is the latest version of  Rotating limit switch cam box with wide range from 3cam to 16 cam having rugged aluminum case with heavy duty shaft and life time scaled Ball-bearing provide the most versatile & dependably.

Rotating Direction                                           Reverse Or Forward

   MAXIMUM ROTATING SPEED

For proxymatry switches                                
For micro switch                                              
Angle between the tooth                                
Shaft Out put                                                  
1000 and above SPM.
250SPM
 5 Degree. 
Dia 16H7
 
  DIGITAL SLIDE/SHUT HEIGHT INDICATOR  

Digital slide adjustment & shut high indicator with having scale factor direction  control & built in encoder. It can be used as slide adjustment as well as shut height indicator.

MECHANICAL DIEMENSION

Mounting Hole of dia 6.5

130mm x 85mm

Over All Dimension

144mm x 102mm

Recommended Opening

85 mm x 115mm

 
    MECHANICAL DIE LIFTER

Spring Loaded Mechanical Die lifter are available from 200mm to 1500mm with  Italian  square spring in three different modal.

1. Basic Model No.:
    18, 20: Light Weight
    30: Heavy Weight.

2. Length of 1 piece
(200 or 300).

3. T/U-Slot "a" dimension.

.MODEL
   No.

Lifting Force Per
100mm(1 line)

T/U-Slot

a

L

DRA 18

0.59kN

18

32~43

DRA 20
Light Load

0.74kN

20, 22, 24

32~43

DRA 30
Heavy Load

1.47kN

28, 32, 36

44~58
 
LENGTH/MODAL NO. 250mm 350mm 450mm 550mm 650mm 750mm 850mm 950mm 1050mm 1150mm 1250mm 1350mm 1450mm 1550mm
DRA18 2.4 3.5 4.7 5.9 7.1 8.2 9.4 10.6 11.8 12.9 14.1 15.3 16.5 17.6
DRA20 2.9 4.4 5.9 7.4 8.8 10.3 11.8 13.2 14.7 16.2 17.6 19.1 20.6 22.1
HRA30 5.9 8.8 11.8 11.8 17.6 20.6 23.5 26.5 29.4 32.3 35.3 38.2 41.2 44.1
 
  DIE LOADING ARM  


Die loading arms both Fixed and Swivel type makes it possible to pull the die out of press to a position where it can be lifted by a crane or fork. Pre roller Aram can be use on servel presses by preparing the press with its mounting blocks on the booster. these are available in eight modal mention below:

  PRA 2 - 7.35KN

  PRA 2L -3.43KN
  PRA 3 -14.7KN   PRA 3L - 14.7KN
  PRA 5 - 14.7KN   PRA 5L - 7.35KN
  PRA 8N - 14.7KN   PRA 8W - 14.7KN
 
  HYDRAULIC POWER UNIT

A high performance ARKEY power unit can generate high hydraulic pressure from compressed air. The hydro/ promatic balance design maintain a constant pressure without consuming any energy. Once the pressure is lost, the unit immediately respond to pump up to pressure the designated level. As opposed to a booster with in (intensifier), The volume of oil displored is not limited to a single stock, But continuously supplied until  the oil pressure reached to the rated lavel. thus makes  the power pack idel for wide range of clamping application. This is available A.6 liter or 2 liter tank. 

SPECIFICATION:-

MODAL

 HUB2-2

HUB6-2

HUB6-22

ARKEY Pump

HPE6308

HPE6308(single)

HPE6308(double)

Discharge pressure

24.7 MPA (0.47MPA)

Discharge Oil volume at no load

1.4l/min.,

2.8l/min.

 
  HYDRAULIC  DIE CLAMP  

This is simple design provides a long clamping stroke and a rugged, low-cost clamp which fits perfectly on dies with U-cuts on the die shoes. The wide range of clamping force from 9.8Kn to 245.0Kn accommodates both small and large presses.
MODAL No. AND SPECIFICATION:-

MODAL

TXA 1

TXA 2

TXA 4

TXA 6

Clamping Force (at pressure 24.5 MPa)

9.8kN

19.6kN

39.2kN

61.7kN

Full Stroke: X(mm) 5 8 8 8
Clamping Stroke: Y(mm) 3 5 5 5
Safety Stroke: Z(mm) 2 3 3 3
Cylinder Capacity (at full stroke) 2 6.5 13 21
 
   HYDRAULIC  DIE -LIFTER

ARKEY series hydraulic lifting die roller are use for having dies with  a maximum capacity of lifting force of 34Kn per cylinder. The length and number of cylinder are determent by the press bed size.
The die can be rolled with a force of 1/100th equal to the die weight 3mm increment length can accommodate a wide range if size and weight. Scrapers are provided to wipe dust and chips out of the rollers. These series are install into a u slot of the press bed. Standard lifting stock of 3mm to 4mm is provided.

MODAL

One Cylinder Capacity

Lifting Force
Per Cylinder(24.5)

Stroke

Max. Load Per Roller by Die material

DLF27 0.54cc 4.45kN 3mm 0.98kN
DLF50 1.50cc 12.05kN 3mm 1.86kN
DLF70 3.60cc 22.25kN 4mm 3.72kN
DLF80 5.60cc 33.91kN 4mm 5.00kN
 
 
Home | Product | Feedback | About us | Contact us

 copyright©webinfosolution